Search Results

A completely new in-line four cylinder engine has been designed at Ford Motor Company for use in the 1984 Tempo/Topaz front-wheel-drive vehicle line. This paper will describe several factors which influenced the engine design, specifically in the areas of improved combustion, reduced friction, electronic controls, packaging and manufacturing. Individual component and overall system designs will also be described.

A technique for making a radiometric measurement of the deposit surface temperature in a methane-fired engine was developed. The wavelength region between 3.5 and 4.1 μm was investigated. It was determined that while the combustion gases were relatively transparent, the surface temperature measurements would contain some gas radiation. A method of averaging the measurements of many cycles and correcting these data for the gas radiation was developed. Time-averaged surface temperature was used in a steady-state heat transfer analysis to determine deposit thermal conductivity. Deposit thermal diffusivity was determined from a transient experiment in which the engine’s ignition system was turned off and the cooling response of the deposit and wall were measured.

The effect of fuel changes on diesel oxidation catalyst performance was studied by comparing the physical, chemical and biological character of the particulate emissions using three different fuels. Baseline (uncatalyzed) emissions were also compared for these same fuels. The fuels used for this study were: a typical No. 2 fuel, a No. 1 fuel, and a shale oil-derived diesel fuel. Comparisons of NOX, NO, NO2, HC and particulate mass emissions using each fuel were made using selected modes from the EPA 13 mode cycle. Changes in the chemical and biological character of the soluble organic fraction (SOF) were also studied. Fuel properties, most notably fuel sulfur content, were found to affect the performance of the oxidation catalyst used. Fuel sulfur content should be kept as low as possible if catalytic converters are used on diesel powered equipment.

The performance of three way and NOx catalysts was evaluated on vehicles utilizing non-feedback fuel control and electronic feedback fuel control. The vehicles accumulated 80,450 km (50,000 miles) using fuels representing the extremes in hydrogen-carbon ratio available for commercial use. Feedback carburetion compared to non-feedback carburetion improved highway fuel economy by about 0.4 km/l (1 mpg) and reduced deterioration of NOx with mileage accumulation. NOx emissions were higher with the low H/C fuel in the three way catalyst system; feedback reduced the fuel effect on NOx in these cars by improving conversion efficiency with the low H/C fuel. Feedback had no measureable effect on HC and CO catalyst efficiency. Hydrocarbon emissions were lower with the low H/C fuel in all cars. Unleaded gasoline octane improver, MMT, at 0.015g Mn/l (0.06 g/gal) increased tailpipe hydrocarbon emissions by 0.05 g/km (0.08 g/mile).

This is the third and final communication in this series of laboratory evaluation of three-way catalysts. The effect of inlet NO concentration and temperature on the NH3 formation over fresh, pulsator-aged and dynamometer-aged three-way catalysts of the current generation has been investigated under temperatures and exhaust compositions of practical interest. In spite of differences in aging procedures employed, both the pulsator and dynamometer-aged catalysts show similar selectivity behavior. The effect of SO2 in feed-gas on gross NO conversion and NH3 formation was studied over Pt-Rh and Pt-Rh-Ru types of three-way catalysts. A strong dependence of the gross NO conversion on the SO2 concentration in exhaust gas mixtures was noted. A simultaneous suppression of gross NO conversion and NH3 formation, in presence of SO2 in feed-gas, is attributed to the poisoning of Pt sites on aged three-way catalysts.

A fundamental thermodynamic model of the complete spark-ignited, homogeneous charge engine cycle has been used in several parametric analyses to predict the effects of engine design and operating alternatives on fuel consumption and emissions of NOx and unburned hydrocarbons (HC). The simulation includes sub-models for wall heat transfer, NOx and HC emissions, and the engine breathing processes. This work demonstrates the power and utility of a comprehensive engine simulation by presenting several independent parametric studies that were carried out in response to genuine engine design and/or operating strategy questions. Included in this compilation are the effects of cycle heat loss, exhaust port heat loss, combustion duration, and charge dilution (EGR and/or lean air-fuel ratio). In addition, the influence of the design variables associated with bore-stroke ratio, intake and exhaust valve lift, and cam timing are considered.

The emission index (grams of species per kilogram of fuel) field within a regenerative turbine combustor has been mapped using a water-cooled sampling probe. The probe employed a choked orifice to simultaneously determine the local temperature. Derived from measurements are: air-fuel ratio, combustion efficiency, average fuel velocity and fuel distribution factor. Methods of averaging the discrete data are developed. A comparison of the data obtained when the combustor was operated on each of two fuels revealed that the use of methanol leads to lower nitric oxide but higher carbon monoxide emission than does the use of diesel fuel.

For the past seven years, the Ford Motor Company has been working on the development of catalytic exhaust treating systems designed to minimize the emission of certain vehicle exhaust gas constituents. In 1959, the development of a low-temperature, catalytic-converter system for the oxidation of exhaust gas hydrocarbons was described in a paper presented to the SAE. That system, which used vanadium pentoxide as the catalyst, has since been extensively developed in a program that included 250,000 miles of converter evaluation on vehicles. Many of the basic system requirements and problems covered in those tests are relevant in vehicle applications of a catalytic converter system with any type of catalyst. With the insertion of a carbon monoxide limit in the California Exhaust Standard, work on the low-temperature, catalytic converter system was discontinued since this system did not, and was not designed to, oxidize carbon monoxide.